Parameters for ES620/Temperature Measurement Module

Enter any name for the hardware module.

Shows the serial number read from the device.

If the hardware is not connected or if it was not found during the hardware search, enter the complete number by hand (it can be found on the device).

The serial number must be entered as it is needed by INCA to identify the device. The serial number is stored in the hardware configuration.

Specifies how the system should react if the connection between INCA and the hardware module is interrupted at measuring start or during measurement.

• Abort after failure

  The measurement using this hardware module will be terminated in any case of measurement failure (at measuring start or during measurement). The system does not try to reinitialize the hardware module. After the connection has been interrupted, you have to reinitialize manually.

  This option is appropriate when, e.g., the measured values are not essential for the experiment, as the module will be ignored after any failure. This option is the default.

• Abort at start, try again later

  INCA stops measurement of this module in case of failure at measuring start, assuming the module is disconnected or has any systematic problem.

  It continues to try measurement in case of failure during the measurement assuming the failure is temporal and can be resolved via retries.

• Retry always

  INCA continues to try measurement of this module in any case of measurement failure (at measuring start or during measurement).

  This option is useful if you want to conduct quick start or cold start measurements.

This specifies whether timestamps are to be rounded or not.

If rounding is enabled, the precision is determined according the following rule:

Divide the acquisition rate by 10 and round to the next smaller power of 10.

Example:

Shows the name of the measurement variable catalog used.

The measurement variable catalog allows you to read the channel parameters for desired measurement variables from a file, thereby reducing the effort required for parameterizing the channel, since channel parameters such as:

• Measure variable name
• Unit
• Sensor calibration information
• Normal measuring range (min./max.)
• Comment

are already specified in the measurement variable catalog.

To select a measurement variable catalog: in the Value column, double-click the field next to Catalog.

Shows information about this module type.

Shows information about this module type.

Displays information about connected devices found during the hardware search.

Shows information about the driver.

Shows information about the fill level.

Shows information about the manufacturer.

Shows information about the state of measurement.

Enter a number to change the channel sequence.

For example, if you enter 1 for channel 3, this channel comes first. The original channel 1 is then moved to position 3.

Enter any name for the measure variable.

Defines the physical unit for displaying the measure variable (°Celsius or °Fahrenheit).

The selected unit appears in the corresponding measure windows.

Defines the acquisition rate necessary for your measurement task.

Defines the currently used sensor type.

This entry affects the physical measurement range that is actually possible (Real range min./Real range max.).

Shows the conversion formula used for the hardware module.

You cannot edit this field.

Defines whether the channel is calibrated.

This enables a sensor offset to be subtracted from the currently measured sensor value before the physical value is calculated according to the sensor formula. If sensor offset mode is enabled, the field is underlaid red.

• off

  No sensor calibration

• automatic phys

  Enter a physical reference value. The sensor offset is calculated automatically.

  Note
  Please note that you need to execute the function Automatic sensor offset adaptation (e.g. via the Hardware menu) for triggering automatic adaptation.

• automatic sensor

  Enter a sensor reference value. The sensor offset is calculated automatically.

  Note
  Please note that you need to execute the function Automatic sensor offset adaptation (e.g. via the Hardware menu) for triggering automatic adaptation.

• manual

  Enter a sensor offset manually.

Enter the physical value to be measured during the automatic offset compensation. The value must be between the defined upper and lower physical values.

You can edit this field only if automatic phys is set in sensor offset mode.

Enter the value of the sensor voltage to be measured during the automatic sensor offset calculation. This value must be between the defined upper and lower values of the sensor signal.

You can edit this field only if you set automatic sensor in sensor offset mode.

Enter the value for the sensor offset.

You can edit this field only if you set manual in sensor offset mode.

In the automatic phys and automatic sensor modes, this value is calculated by INCA.

Enter the lower limit of the expected physical measurement range.

This value is used in the experiment, for example for the Y-axis scaling in the oscilloscope.

Enter the upper limit of the expected physical measurement range.

This value is used in the experiment, for example for the Y-axis scaling in the oscilloscope.

Shows the lower physical limit of the measurement range actually possible for this channel.

This value is determined by the entry under Sensor type.

You cannot edit this field.

Shows the upper physical limit of the measurement range actually possible for this channel.

This value is determined by the entry under Sensor type.

You cannot edit this field.