XETK-S22.0B

Defines the type of the microcontroller used in the ECU.

Defines the frequency used for the JTAG interface.

When ResetOut signal is used, JTAG Initialization Reset Delay [us] should be 0.

This ETK always monitors the Reset signal to determine the microcontroller’s reset status. This feature determines if the ETK additionally monitors the ResetOut signal to determine the microcontroller’s reset status.

Selects the polling rate in μs. Typically at least twice as fast as the fastest raster in a measurement.

Selects how the XETK controls the ECU watchdog.

• Controlled by ECU: The XETK will not drive the signal.
• Enabled: Enables watchdog control from the XETK debugger connector. The XETK will drive the signal as configured to enable the watchdog when the debugger requests the watchdog to be enabled.
• Disabled: The XETK will drive the signal as configured to disable the watchdog.

Controls which level of the watchdog disable signal shall disable the watchdog.

• Low: Low level shall disable the watchdog.
• High: High Level shall disable the watchdog.

The (X)ETK has the ability to wake up the ECU by applying voltage to the CalWakeUp pin of the ECU connector. This makes it possible to download the content of the working page and configure a measurement while the ECU is off.

When waking up the ECU via the CalWakeUp pin it can be selected whether the pin is pulled until the microcontroller core voltage (VDDP) is high or whether the pin should be kept on high state until the start-up handshake between ECU and (X)ETK signals to the (X)ETK that the ECU has finished its initialization.

• YES: The CalWakeUp pin will be kept on high state until the start-up handshake between ECU and (X)ETK signals to the (X)ETK that the ECU has finished its initialization.
• NO: The CalWakeUp pin is pulled until the microcontroller core voltage (VDDP) is high.

Selects the voltage the (X)ETK will use for ECU power supply supervision.

Selects the voltage the (X)ETK will use for ECU standby RAM (working page) power supply supervision.

Selects the ECU bus voltage or lets the XETK device detect the voltage.

The XETK device will drive the data bus of the ECU using the voltage level according to the selected entry.

Selects the standby voltage the (X)ETK will provide to the ECU for the working page.

Selects the signal the (X)ETK will use for ECU standby RAM (working page) power supply supervision.

• ETK Standby Supply: (X)ETK is monitoring the standby supply it provides to the ECU.
• ECU Standby Supply: (X)ETK is monitoring the ECU standby supply; the ECU is not using the standby supply from the (X)ETK.
• No Standby Supply: (X)ETK is monitoring the standard ECU power supply; the working page is not using a standby supply.

Defines the hardware handshake timeout in case the ECU did not perform or does not support a hardware handshake.

To force the ECU to perform the handshake, enter -1 (infinite).  Using this setting, measurement and calibration is only possible if the ECU performs the specified handshake type.

Otherwise enter a value between 0 and 65534 ms.  The value should be set to the earliest time the XETK should access the ECU memory after the ECU is running (both powered and out of reset).

Enables Advanced Handshake between ETK and ECU. If it is not enabled Legacy Handshake is performed instead.

Selects how many register triggers are polled by ETK. All options support multicore systems, however for those which only Core 0 is read, all cores must be able to write to Core 0 registers:

• Core 0, 32 bits: ETK polls 1 register trigger of Core 0. 32 HW triggers can be used.
• Core 0, Core 1 and Core 2, 32 bits: ETK polls 1 register trigger per core. The result is combined into 32 HW triggers (that's an option for multicore system where other cores cannot write to Core 0 registers).
• Core 0, 64 bits: ETK polls 2 register triggers of Core 0. 64 HW triggers can be used.
• Core 0, 96 bits: ETK polls 3 register triggers of Core 0. 96 HW triggers can be used.
• Core 0, 128 bits: ETK polls 4 register triggers of Core 0. 128 HW triggers can be read.
• Core 0, 160 bits: ETK polls 5 register triggers of Core 0. 160 HW triggers can be read.
• Core 0, 192 bits: ETK polls 6 register triggers of Core 0. 192 HW triggers can be read.
• Core 0, 224 bits: ETK polls 7 register triggers of Core 0. 224 HW triggers can be read.
• Core 0, 256 bits: ETK polls 8 register triggers of Core 0. 256 HW triggers can be read.

Selects the behavior of the Flash Mode pin (FLMD0):

• Flash Mode: ETK drives this pin in flash mode signal.
• Watchdog Disable: ETK drives this pin as watchdog signal.

Defines how the XETK shall behave if an overload occurs during data processing.

• Drop Data and Continue Measurement: The XETK drops measurement data, sends an error event and continues measurement.
• Stop Measurement: The XETK stops the measurement and sends an error event.

Selects the ETK Standby Mode:

• Standard: shorter boot time - higher standby current.
• Deep: longer boot time - minimum standby current

Configures whether the ECU is set into reset during ETK sleep. This may improve the handshake after wakeup.

In case Enhanced Coldstart is used it defines the base address of the Distab Checksum array.

• 0xFFFFFFFF: Enhanced Coldstart is not used.
• Any other value: Enhanced Coldstart is used. The value is the base address of Distab Checksum array.

Selects the behavior of /RDY pin provided to debugger:

• /RDY: Ready output
• /Power-down BIST status: Select this option in case power-down BIST is desired with debugger connected.

Selects how ETK controls /TRST:

• Default: ETK asserts /TRST based on ECU Reset
• Asserted with power-down BIST trigger: ETK asserts /TRST based on ECU Reset and power-down BIST trigger

This feature should be set to "Default" if power-down BIST with ETK connected is not required.

Defines the method of serial memory access:

• Default: Standard memory access using RH850 “Type A” full access sequence.

• Optimized Block Read: Improves performance by utilizing an optimized RH850 “Type A” access sequence for contiguous/block reads, omitting redundant JTAG IR scans.

• Optimized Scattered Read: Improves performance by utilizing an optimized RH850 “Type B” access sequence for scattered or contiguous/block reads.